12/26/2004
0:58		TRD latch-up (cal trigger is 0.6Hz)	HP
1:00		TRD started working after first ped-run file	HP
1:15		TRD latch-up (cal trigger is 0.2Hz)	HP
1:21		TRD started working after first ped-run file	HP
1:26		TRD latch-up (cal trigger is 2.0Hz)	HP
1:31		TRD started working after first ped-run file	HP
1:48		TRD latch-up (cal trigger is 2.0Hz)	HP
1:51		TRD started working after first ped-run file	HP
2:10		TRD latch-up (cal trigger is 0.1Hz)	HP
2:12		TRD started working after first ped-run file	HP
2:41		TRD latch-up (cal trigger is 1.2Hz)	HP
2:52		TRD started working after the second ped-run file	HP
2:54		Send "get_spi.stol"	YS
3:16		TRD latch-up (cal trigger is 1.2Hz)	HP
3:22		TRD started working after first ped-run file	HP
3:33		TRD latch-up (cal trigger is 3.0Hz)	Hp
3:41		Cal trigger rate become around 10-18	YS
		Buffer (PKT0 goes up to 5%)
		Next command window will start 4:24(EST)
3:50		Hoskeeping does not updtaed. Data flow looked stopped	YS
		ESC said they are going to make it back.
4:02		ESC said data is still coming from sfc, but there is some problem on ground computer. They are going to reboot their computer	YS
4:07		Connrction comes back..	YS
		Cal trigger rate is still too high about 10-18..
4:14		Buffer (PKT0) became 20%. Command window will be open in 10 minutes	YS
4:19		TRD starts working after  the fourth ped-run file	HP
4:22		TRD latch-up (cal trigger is 17.0Hz)	HP
4:25		cal trigger threshold 70	YS
		CAL trigger rate become around 1-3 Hz	YS
		Buffer(PKT0) goes down slowly.	YS
4:56		TRD starts working after  the fourth ped-run file	HP
4:58		TRD latch-up (cal trigger is 2.0Hz)	HP
5:20		Buffer(PKT0) is cleared 0%	YS
5:23		TRD started working after the third ped-run file	HP
5:32		TRD latch-up (cal trigger is 3.0Hz)	HP
5:33		TRD started working after the first ped-run file	HP
5:40		TRD latch-up (cal trigger is 1.0Hz)	HP
5:43		TRD started working after the first ped-run file	HP
5:50		TRD latch-up (cal trigger is 2.6Hz)	HP
5:53		TRD started working after the first ped-run file	HP
6:04		TRD latch-up (cal trigger is 2.6Hz)	HP
6:14		TRD started working after the first ped-run file	HP
6:21		TRD latch-up (cal trigger is 4.3Hz)	HP
6:23		TRD started working after the first ped-run file	HP
6:29		TRD latch-up (cal trigger is 2.6Hz)	HP
6:33		TRD started working after the first ped-run file	HP
6:39		TRD latch-up (cal trigger is 2.6Hz)	HP
6:43		TRD started working after the first ped-run file	HP
6:49		TRD latch-up (cal trigger is 5.0Hz)	HP
6:54		TRD started working after the first ped-run file	HP
7.09		TRD latch-up (cal trigger is 5.0Hz)	HP
7:12		Send "get_spi.stol"	YS
7:24		TRD started working after the first ped-run file	HP
7:26		TRD latch-up (cal trigger is 6.0Hz)	HP
7:34		TRD started working after the first ped-run file	HP
7:39		TRD latch-up (cal trigger is 6.0Hz)	HP
7:44		TRD started working after the first ped-run file	HP
7:59		TRD latch-up (cal trigger is 2.3Hz)	HP
8:04		TRD started working after the first ped-run file	HP
8:19		TRD latch-up (cal trigger is 2.5Hz)	HP
8:34		TRD started working after the second ped-run file	HP
8:40		TRD latch-up (cal trigger is 7.9Hz)	HP
9:03		TRD started working after the third ped-run file	HP
9:07		TRD latch-up (cal trigger is 2.0Hz)	HP
9:23		TRD started working after the second ped-run file	HP
9:29		TRD latch-up (cal trigger is 1.4Hz)	HP
9:46		TRD started working after data file	HP
9:54		TRD latch-up (cal trigger is 3.2Hz)	HP
9:56		TRD started working after data file	HP
10:01		TRD latch-up (cal trigger is 3.4Hz)	HP
10:09		cal trigger threshold 72	JH
10:17		TRD started working after data file	HP
10:19		TRD latch-up (cal trigger is 1.4Hz)	HP
10:26		TRD started working after data file	HP
10:41		TRD latch-up (cal trigger is 1.2Hz)	HP
10:46		TRD started working after data file	HP
11:04		TRD latch-up (cal trigger is 0.6Hz)	HP
11:17		TRD started working after data file	HP
11:09		TRD latch-up (cal trigger is 0.0Hz)	HP
11:16		TRD started working after data file	HP
11:28		ssssssss	HP
11:47		TRD started working after data file	HP
11:51		TRD latch-up (cal trigger is 1.4Hz)	HP
12:07		TRD started working after data file	HP
12:24		TRD latch-up (cal trigger is 0.8Hz)	HP
12:27		TRD started working after data file	HP
13:25		changed pedestal run every 5 minutes	JH
13:45		TRD latch-up (cal trigger is 1.2Hz)	HP
13:46		TRD started working after data file	HP
14:29		TRD latch-up (cal trigger is 1.2Hz)	HP
14:37		TRD started working after data file	HP
14:54		TRD latch-up (cal trigger is 0.2Hz)	HP
14:57		TRD started working after data file	HP
15:26		TRD latch-up (cal trigger is 0.5Hz)	HP
15:27		TRD started working after data file	HP
15:29		Send "get_spi.stol"	JH
15:30		TRD latch-up (cal trigger is 0.5Hz)	HP
15:32		TRD started working after data file	HP
15:42		TRD latch-up (cal trigger is 1.0Hz)	HP
15:47		TRD started working after data file	HP
17:23		TRD latch-up (cal trigger is 0.4Hz)	HP
17:24		TRD started working after data file	HP
18:03		TRD latch-up (cal trigger is 0.2Hz)	HP
18:08		TRD started working after data file	HP
18:12		rebalance top TRD	JH
		ramp down TRD HV1, open valve 32-35, close valve 32-35
		ramp up TRD HV1 to 1.53KV
		rebalance bottom TRD
		ramp down TRD HV2, open valve 10-13, close valve 10-13
		ramp up TRD HV2 to 1.56KV
		the above two are required by Simon
19:35		TRD latch-up (cal trigger is 0.2Hz)	HQ
19:40		TRD started working after data file	HQ
20:10		TRD latch-up (cal trigger is 0.2Hz)	HQ
20:15		TRD started working after the first ped-run file	HQ
20:35		TRD latch-up (cal trigger is 0.6Hz)	JH
20:40		TRD started working after opening data file	JH
21:35		TRD latch-up (cal trigger is 0.2Hz)	JH
21:41		TRD started working after the first ped-run file	HQ
22:06		Send "get_spi.stol"	JH
23:52		TRD latch-up (cal trigger is 0.2Hz)	HQ
23:57		TRD started working after the first ped-run file	HQ